| |
G8MNY > TECHNI 26.05.19 09:43l 155 Lines 6565 Bytes #999 (0) @ WW
BID : 6191_GB7CIP
Read: GAST
Subj: PERFORMANCE POWER 1kW Genny
Path: DB0FFL<OE2XZR<OE5XBL<F1OYP<ON0AR<OZ5BBS<CX2SA<OK2PEN<GB7CIP
Sent: 190526/0837Z @:GB7CIP.#32.GBR.EURO #:6191 [Caterham Surrey GBR] $:6191_GB
From: G8MNY@GB7CIP.#32.GBR.EURO
To : TECH@WW
By G8MNY (Updated Jul 17)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
I was given this 87cc genny, it was very clean & hardly used, but been garage
stored (some corrosion) for a few years. It was supplied by NuTools. In layout
it is very similar to my much bigger well-used MEDUSA SIP2300 2.3kW one.
ÜßßßßßßßßßßßßßßßßßÜ Û _________ðððð_________ Û Tube
Û/~~~~~~Tank~~~~~~~\Û Û/" 6L Tank "\Û Cage
Û-------------------Û Fuel Tap Û==========================Û
ÛÄÄÄÄÄÄÄÄÄÄÄÄÂÂÄ/~~~Û & filter\Ûo~~~~~~~~~~~~~~~~~~~~~~~~oÛ
Û Tap(0)³elecÛ STOPÛ [] onø_ø±A±³øTrip Û DC 1x 2Pin
ÛChoke // \___Û SWITCHÛo off ³V³±C±³-| DC oÛ AC 1x 13A
ÛÚÄÄÄÄ¿ /~~~~~\\. ÛPull ÛÂÄÄÂÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÂÂÛ
Û³In- ³,' /~~~\/\\ ÛStart Û³F ³ENGINE ³ð ³ ³³Û
Û³Take³³ ³ ( ) ³ ³ Û Û³A ³ oil(=)³ð ALT ³ ³³Û
ÛÀÄÄÄÄÙ \ \___/ / Û Û³N ³ _____³_³³ð______³__³³Û
Û Ú' ÚÄÄÄÄÄ¿ `¿ Û ßÜÄÄÁÄÄÄÜÙ ~~~ ÀÜÁÁÜß
ß"""""""""""""""""""ß ßßßßßßßßßßßßßßßßßßßßßßßß
STARTING ENGINE
It started on "easy start" ether spray OK. But the mixture was very lean & need
the choke partly on, to run for several minutes. (old Petrol?) I striped down
the carb & clean the main jet, then it was a little better.
PETROL TAP
There is next to no tank sump, so an unlevelled ground may result in fuel
starvation, despite there being quite a bit of fuel left. This not helped by
the "in the tank" hidden fuel filter & a fully "screwed in" tap!
Ú¿
Min Petrol ³³-Filter
Level---³³ So make sure the tap in only "just" (2 turns)
ÄÄÄÄÄÄÄÄÄÄÄ¿__ÜÝÞÜ__ÚÄÄÄÄÄ screwed into the tank, & then do up sealing Nut.
Sump/ ±±±±\O ring
Unused thread _ ÝÞ & Nut
_ÝÞ_
____/ __ \
Carb Pipe ____ (Þ_) )
\_Þ__/
ÞTap
CIRCUIT
No circuit in the handbook etc. So I have reverse engineered this diagram.
12V F R O N T 240V AC STOP
Charging P A N E L ÚÄÄÄÄÄ¿ ÚÄo\__
³+ -³ E _³_ ³bk bk³ Earth
3A Bridge ÚN L¿ /// _³_ ³ _³_
Rectifier ³ ³ /// ³ ///
³ ³ ÃMeter´ ³
4A* ³ ³ 4A ³
Trip ³ ³ Trip ³
³ gn³ ³ ³ ³
³gn ³ 12u 450V ³bk rd³ External³ Pointless
- í - í - - - - - - í -- í - - - - - - - - - ³ - - - - -
³ ³ ÚÄ´ÃÄÄ¿ ³ ³ ÚÄÄRÄÄ¿ | Magneto³ Coil
³ ³ íye yeí ³bn bn³ ÃÄ´>ÃÄ´ | ÚÄÄ()))))ÍÍÍÍÍÍ»
³.4ê³ ³ 9.6ê³ ³ 4.3ê³ ³ ³ | ³0.2ê 5k6 ºEHT
À())Ù À(((()Ù À(((()Ù À(((()Ù | ³ ÚÄ> <Í1/4
=== ===== ===== ===== | _³_ _³_ Plug
Load Exciter Load Rotor | /// ///
A L T E R N A T O R | F L Y W H E E L
ALTERNATOR EXCITATION
This is a brush less alternator, with the excitation of the rotor magnetically
charged up each half cycle from circulating 90ø out of phase currents from the
exciting 12uF capacitor. The rotor winding has a diode across (& back emf R) it
to maintain the current half a cycle after the kick (100 times a sec).
Excitation starting with the weak residual magnetic rotor field, needs at high
enough RPM (2000RPM) to overcome the rotor diode voltage drop, About 10% of the
power is needed for excitation of the rotor, hence alternator fan must be kept
efficiently working.
This system is more reliable than the DC to brushes & slip rings type, but it
does produce a slight kink in the load winding waveform & there is no
opportunity for voltage control other than engine RPM.
CHARGING (20V off load)
The genny came with the special DC plug & lead (- |), but the lead is short &
the trip was only 4A, & it trips all the time @ it's rated 5-6A charging
current, unless the RPM is well reduced. So I swapped the trip for 10A more
reasonable rated one.
The rectifier is only made from 4x 3A diodes inside the connector socket, with
no heat sink! To improve on this, I doubled up on the diodes, putting 4 more
1N5402 diodes on the copper side of the PCB & flowing lots of solder on the
tracks to improve heat dissipation. Note the current trip does not prevent
blowinc the diodes on wrong battery polarity! So a 13A fuse in the charging
lead will help that!
AC REGULATION
This is a simple bob weight & spring RPM controlled engine governor, with the
alternator's capacitor self-exciting winding at 90ø to the load winding which
gives some load to voltage compensation. On this generator these two features
alone seem to give quite good results.
Load Volts
0W 240
275W 237
500W 235
775W 230
1000W 220
1100W 215 Max Throttle!
IGNITION NOISE
This was quite high, noticeable on HF - UHF, as there are NO suppression parts,
despite the CE compliance markings etc. I did 3 things to get it down 30dB.
1/ Change the spark plug for a resistive type (measures between 5K-15K) it must
be same reach & ideally same temp type.
2/ I added a non-inductive 5K6 in series with spring inside the spark plug cap.
(ÞßÝ part unscrews)
.--------
| _==== < spike
S=Shortened Spring | S Ú----
R=5k6 bare ends | R |
|ÞßÝ|
| |
| |
3/ Then I added a coax braid over the EHT lead & earthed it at the cylinder
head. The braid is kept insulated other than at the cylinder head end!
.-----================================----- EHT Lead To
|nÚ---================================ÄÄÄÄÄ Magneto coil
³~³ // Added Coax Braid
ÚÙ À¿ ||
ݱ±±Þ || Braid earthed
Cylinder ÄÅÄÄÄÅÄÅÅ to head bolt
Head À~u~Ù with a tag.
Spark Plug
OTHER MODIFICATIONS
A/ Reduced the tappet clearence as it was quite noisy (rattly).
B/ As with other Gennys, I added an earth lead to clip on earth stakes etc.
C/ And also the 13A socket rattles any plug out a in a few mins, so a Bungee is
needed stretched over the plug to keep it in.
See my TECH buls "Regulating 12V Generator Output", "MEDUSA SIP2300 Generator
info", "MEDUSA SIP2300 Generator Repairs", "Cheaper Generators" & "Petrol
Generators for /P SSB"
Y Don't U send an interesting bul?
73 de John G8MNY @ GB7CIP
Lese vorherige Mail | Lese naechste Mail
| |
