OpenBCM V1.07b12 (Linux)

Packet Radio Mailbox

DB0FFL

[Box DB0FFL]

 Login: GAST





  
G8MNY  > TECHNI   31.10.18 11:21l 347 Lines 16528 Bytes #999 (0) @ WW
BID : 43595_GB7CIP
Read: GAST
Subj: Valves (Tubes)
Path: DB0FFL<OE5XBL<F1OYP<IR2UBX<IZ3LSV<IK6ZDE<VE2PKT<OK2PEN<GB7CIP
Sent: 181031/1016Z @:GB7CIP.#32.GBR.EURO #:43595 [Caterham Surrey GBR]
From: G8MNY@GB7CIP.#32.GBR.EURO
To  : TECH@WW

By G8MNY                                   (Updated Sep 16)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)

Although Valves are considered old hat nowadays, they are still used in big Tx,
RF heating systems, microwave ovens, & of course in lots of old kit.

Here is some valve information for anyone who wants to brush up on the basics.

HT VOLTAGES
Most valves use quite high voltages, the High Tension e.g. 90, 120, 200, 250,
350, 1k5V 2kV, 3kV etc. Only a few special Rx valves use voltage as low as +12V
HT.

So care must be taken if you don't want a nasty HT nip or even DEATH!

HEATERS VOLTAGES
Only special cold cathode & gas filled valves need no heaters. The heater power
can be quite large compared to the total power. For battery radio valves heater
voltages of 1.4V or 3V are normal. The most common voltage is 6.3V & for mains
heater chains where all the heater in a set are in series, either 0.3 or 0.1Amp
are the 2 common standards with a dropper resistor (line restistance cord), AC
capacitor, or diode to make up the mains supply voltage. Negative temperature
thermistors were commonly put in mains chains, to take the warming up shock
from the cold low resistance heaters.

On diagrams the heater chain/wiring is normally not drawn with the rest of the
stages.

CONNECTIONS
Like lamps Valves have limited lifetimes 2000 hours for the bigger ones &
>20,000 hours for CRTs etc. Turning them off & on is oftem more limiting that
leaving on! Most come with a pin connection base standard for easy replacement.
These are give names like... B7G, B9A, MO, IO, P, P5, B9, B7, B5/4, UX7, UX5,
UX4, etc.
     _ 
    ³ ³ Top Cap
 .ú'~~~'ú.
/         \
³         ³                                             ___
³         ³ GetterÄÄ.úüú.                              /   \
³         ³ Marks  ³     ³Glass       ³           ÚÄÄÄÁÄÄÄÄÄÁÄÄÄ¿Finned
³         ³/       ³     ³Envelope   /~\          ³   4CX250B   ³External
³         ³        ³     ³          ³   ³         ³             ³Anode
 \       /         ³     ³       ÄÄ=======ÄÄ      ÀÄÄÂÄÄÄÄÄÄÄÂÄÄÙ
 ÃÄÄÄÄÄÄÄ´         ³     ³           \_/         G2 ÚÁÄÄÄÄÄÄÄÁ¿~\Ceramic
 ³       ³         ÀÂÂÂÂÂÙ            ³       ScreenÀÄÂÂÂÂÒÂÂÄÙ Insulator
 ÀÒÒÒÒÒÒÒÙ       Through glass      Acorn      Ring   ³³³³º³³
  ººººººº         wire pins         Type                ÀĽ
 Soldered on                                         Central Grid
valve base pins                                      Locating Pin

Many valves have top cap connections usually for Anodes on Tx & power valves
like TV sweep tubes, but may also be a sensitive control Grid on Rx valves!

Getter marks are shiny silver/black areas where Magnesium has been vaporised
onto the glass to catch the last remnants of gasses in the evacuated tube. A
white getter mark indicates air has got into the valve & it is useless!

With the all glass construction & a good magnifying glass, it is often possible
to determine not only what the internal constructions are (diode, triode,
pentode etc.) but often also their pin out connections. But I have seen
tetrodes assemblies wired up as a "rectifier diode internally" though (must
have had a surplus?).

INTERNAL CONSTRUCTION                 _____
Most valves are cylindrical          /     \ Anode
design with the Anode &             /.ú'''ú.\       ú  = Grid Wire
Cathode electrodes as              ( í (*) í )      í  = Grid Support
coaxial tubes with wire grid        \'ú...ú'/      ( ) = Cathode tube
structures between them.             \_____/        *  = Heaters
Punched Mica sheets then            plan view
support the supports.

VALVE NUMBERS
There are several systems! Some reflect the heater voltage & valve type, while
others have no meaning at all.
    EBC33 has 6.3V heaters (E), having Diode detector (B) & a Triode (C) with
    electrical & connection valve type 33.
    CV123 is a UK military type, often with loads of commercial equivalents.
    12AU7 is a 12V heaters (2x 6.3V) double triode.

A good valve data book will give you all the information for the type number &
include direct equivalents. But like transistors, many applications may not
need a direct equivalent, but electrode connections & heater voltages are most
important to get right!

CATHODE
The Cathode can be directly heated
by current through the Cathode wire,                      Indirectly Heated
or indirectly heated with insulted        ³     ³ Glass        Cathode
wire inside the Cathode tube.              \/~\/ envelope     ³  /~~\ ³
Electrons boil off the hot Cathode          ³~³                \³_/\_/
electrode, normally helped buy an         Directly              ³ ³³
emitting coating enabling lower          Heated Wire              Heaters
temperatures to be used (dim red glow).    Cathode
Without the coating the Cathode has
to be very HOT, more like a lamp!

Directly heated Cathodes on AC supply often use a centre tapped AC supply, or a
"hum dinger" pot across heater line to minimise hum due to the heater voltage. 

The boiled off electrons form a cloud in the vacuum, & can be attracted to the
Anode electrode if it is positive (or very near) with respect to the Cathode.

ANODES
These attract the electrons & have to
absorb kinetic energy from the fast           ³
moving electrons & radiate it as heat.      .-³-.
On power valves Anode structures are       / ÄÁÄ \
designed to radiate the heat away,        ³ Anode ³
or may even be externally finned to
do this.

If the electrons are very fast then they can dislodge electrons in the Anode
causing secondary emission from the Anode to other electrodes. To stop this
some power valves use carbon/carbonised Anodes which better soak up electrons
to stop most of this unwanted emission.

DIODES
These use the 2 electrodes in an            Anode
evacuate tube to conduct current            .-³-.
one way.                                   / ÄÁÄ \
                                           \ /~\ /
Note that electrons flow the                '³-³'
opposite way to current e.g. -ve to        Directly
+ve, as electrons were discovered           Heated
after the properties of current            Cathode
had been determined.

Unlike solid state devices, there is no voltage drop across valve signal diodes
as the nearby Cathode electron cloud actually gives up electrons freely to the
Anode (space charge current).
                                           Anode
                                           .-³-.
In Rx valves, they are often              / ÄÁÄ \
part of a multi valve single tube    G1 ÄÅ - - - ³
for IF detectors & AGC detectors     D1 ÄÅÄ´/~~\ÃÅÄ D2
plus the 1st AF amp stage.                \  /\³ /
                                           ~~³³³~
                                             HH Cathode

RECTIFIERS                             350VAC   350VAC
These are just powerful                Anode1   Anode2
versions of the diode                     .ú³-Ä-³ú.
used in power supplies.                  / ÄÁÄ ÄÁÄ \
                                        ³           ³
Bi-phase designs are                     \ /~~~~~\ /
common.                                   ~³ÄÄ-Äij~
                                           ³4V 2AÃÄÄÄ>+350V DC 
Voltage drop may be up to 30V @100mA.       Heater

Efficiency diodes rectifiers used in old TV stages, unusually have the Cathode
as the top cap with very good Cathode to heater insulation for several kV.

TRIODES                            +150V HTÄÄÄÂÄ
These have a Control Grid                    47k         Large inverted
between the Cathode & Anode                   ÃÄÄÄÄÄ´ÃÄÄÄ Output
that reduces the flow of                    .-³-.  0.01uF
electrons. Gain "gm" or "mu"         10n   / ÄÁÄ \  250V
is in Anode mA per Grid Volt.       Ä´ÃÄÂÄÅ - - - ³
The Grid is usually negative    Input   ³ ³ /~~~\ ³
with respect to the cathode,           1M  \ /\ ³/
& an AC bypassed cathode            grid³   ~³³~ÃÄÄÄ¿+
resistor is a common way to         leak³    HH ³  ===
obtain this bias.                       ³       1k  ³ 25uF
                                      ÄÄÁÄÄÄÄÄÄÄÁÄÄÄÁÄ
There is quite high capacitance between the Anode to the adjacent Grid & this
causes high frequency negative feedback (Miller effect) in these high impedance
circuits. The electron flow is proportional to the Grid voltage, but also the
attracting Anode voltage, so there is considerable negative feedback in the
triode, which keeps the Anode impedance low in common Cathode mode.

                                             ÚÄ +1500V HT
Common Grid mode (drive on the Cathode)      )RFC
is used in some PA & RF amp designs          ÃÄÄÄÄÄ´ÃÄÄÄ Output to
with its reduced power gain, it has        .-³-. 1n 3kV   pi Tank
the advantage of no Miller effect as      / ÄÁÄ \
well as applying current NFB, making     ³ - - - ÅÄÄ¿
the stage stable, quite linear & with    ³  /~\  ³ _³_
low impedance drive.                      \_³ ³_/  ///
                             RF Drive ÂÄ´ÃÄÄ´ ³ RF Floating
                                      ÀÄÄÄ´Ã)Ä´ Heaters & Cathode DC

For large Tx valves the triode may even be run with no bias & very large
amounts of Grid current, when the Grid is pushed positive by the drive signal,
but the Grid must be designed for this, or it will be destroyed! In data books
you see mode of operating "class A B or C" with suffix "1 or 2", 1 indicates NO
grid current 2 is with Grid current.

TETRODES
These have 2 Grid electrodes,       HTÄÄÄÂÄÄÄÄÂ_    ___
a control Grid (G1) & a screen          10k     )||(  LS
Grid (G2). The screen Grid               ³     _)||(___
provides screening for G1                ³  .-³-.  25:1
from the Anode reducing the              ³ / ÄÁÄ \
Miller effect & also                     ÀÅ - - - ³
maintaining a + attracting          InputÄÅ - - - ³
electrode other than the Anode            ³ /~~~\ ³
reducing the Triodes NFB                   \³_/\_/
effect & increasing gain.        100uFÚÄÄÄÄÄ´ ³³
Tetrodes are commonly used in        ===   220
AF output stages.                   ÄÄÁÄÄÄÄÄÁÄ

BEAM TETRODE                                  A
These have extra earthed                    .ijÄ.
electrode structure (attached              / ÄÁÄ \
to cathode) shielding much of             ³ ]   [ ³
the Anode structures electrical       G2 ÄÅÄ - - \³
effects from the Grids.               G1 ÄÅÄ - - ³³
The Grids may also be exactly             ³ /~~~\/³
in line to improve efficiency,             \_/\_³/
by keeping G2 currents low.                  ³³ ³C

PENTODES                                      A
These have an earthed suppressor            .-³-.
Grid (G3) between the screen               / ÄÁÄ \
Grid (G2). This also does Grid        G3 ÄÅÄ - - |³
Anode shielding, but also reduces         ³  - - ÄÅÄ G2
secondary emission effects,           G1 ÄÅÄ - - |³
improving gain & linearity.               ³ /~~~\ÀÅÄ Screening
For RF signal amplifiers an outer          \³_/\_/
painted on or inner electrical             C³ ³³
screening may be used.

Variable gain (mu) can be obtained        Stage
if the pitch of the G1 wire in            Gain
manufacture is made variable, then      100%´ú..ÄÄ--.._  Normal Valve Cut
increasing the -ve bias will slowly      75%´   ''úú.. \ Off & Distortion
reduce the small signal gain of the      50%´ Variable''\ú..
valve rather than just cut off the       25%´  Mu Gain   \  ''úú.._
whole valve. Rx AGC & Tx ALC use          0%ÅÄÄÄÄÂÄÄÄÄÂÄÄÄÄÂÄÄÄÄÂÄÄ~ Bias
this feature to control gain.               1    2    3    4    5   -Volts

                                          Anode IF
HEPTODES                                    .-³-.
With more electrodes                       / ÄÁÄ \
some valves can be a       Suppressor G5 ÄÅÄ - -  ³
mixer plus oscillator                     ³  Ä - ÄÅÄ G4 Osc Anode
using the same                            ³  - - ÄÅÄ G3 Osc Grid
electron flow.            Screen Grid G2 ÄÅÄ - -  ³
                          RF signals  G1 ÄÅÄ - -  ³
                                          ³ /~~~\ ³
                                           \³_/\_/
                                           C³ ³³
BEAM MIXERS
A good performance mixer can be            A1   A2
made using a balanced out of              .-³-Ä-³-.
phase Anodes A1 & 2, & a pair            / ÄÁÄ ÄÁÄ \
of beam bending deflection          P1 ÄÅÄ´       ÃÄÅÄ P2
plates P1 & P2 fed with the             ³   - - - ÄÄÅÄ G2
balanced local oscillator.          G1 ÄÅÄÄ - - -   ³
The amplified radio signal on           ³  /~~~~~\  ³
G1 is then fed in turn to A1 or          \³__/~\___/
A2 depending on of the phase of          C³  ³~³
the balanced local oscillator.

MULTIPLE VALVES                           At     Ap
As vales are quite big it is            .-³-ÄÄÄÄ-³-.
quite common to include more           / ÄÁÄ    ÄÁÄ \
than one in a glass envelope if       ³      Ú - - - ³
there will be no interference    G1t ÄÅÄ Ä Ä ³ - - Ä ÅÄ G2p
(e.g. not multiple RF stages).        ³      ³ - - Ä ÅÄ G1p
Here a detector Diode, audio      D1 ÄÅÄ´ /~~~~~~~\  ³
Triode & audio output Pentode          \    /~~\  ³ /
all share the same Cathode.             ~~ijÄ--ij~³~
Sometimes in a diagram only part           H    H C
of the valve may be shown in a
part of the circuit.
                                          A      A'
Some push pull VHF/UHF Tx valves       .--³-ÄÄÄÄ-³--.
use twin beam tetrode assembles       /  ÄÁÄ    ÄÁÄ  \
with one Cathode & G2, but two       ³  ]   [  ]   [¿ ³
G1s & Anodes. Internal Anode     G2 ÄÅÄ - - -ÄÄ- - -³ ³
to Grid neutralising capacitors  G1 ÄÅÄ - - -  - - -³ÄÅÄ G1'
between A'- G1 & A - G1' are         ³  /~~~~~~~~~~\³ ³
possible with push pull valves        \___  /~\  ___³/
in one envelope.                          ~~³~³~~   ³C

INDICATOR TUBES
Often called magic eye or tuning
indicators, these give a varying          A1     A2
area of green fluorescent display         .³-ÄÄÄ-³-.
depending on the signal. They are        / ÃÄÄ¿  ³  \
commonly twin triodes, where the        ³ ÄÁÄ ³ ÄÁÄ  ³
anode of the first is the beam       G1ÄÅ Ä Ä ÀÄ Ä Ä ³
altering grid of the second triode      ³  /~~~~~~~\ ³
& connected to HT with a high value      \³___/~\___/
resistor. The second triodes' anode      C³   ³~³
at HT is phosphor coated, or used
as an accelerator anode to phosphor
on the glass to give the display.

BEAM TUBES
Many types of special electron beam tubes exist other than the Cathode Ray Tube
they include Travelling Wave Tubes, Klystrons etc. Most amplify or self
oscillate & can produce very useful gains (e.g. 40dB) & powers (kW) at some
astonishing frequencies (10s of GHz).

GAS FILLED
Gases are normally not wanted in valves as it ionises & poisons the Cathode.
But cold Cathode tubes using neon, or other gasses do make good shunt voltage
regulators (like zeners), & even triggered timebases using a Thyratron. The DOT
or sometimes hatching, represents the gas inside the envelope.

                   +                   .-³-.
  .-³-.           .-³-.      Trigger  / ÄÁÄ \          .-³-ÄÄ-³-.
 / ÄÁÄ \         / ÄÁÄ \       Gate ÄÅ - -ø- ³        / ÄÁÄ  ÄÁÄ \
³  ù    ³       ³    ù  ³      Grid  ³ /~~~\ ³       ³      ù     ³
 \ ÄÂÄ /         \Ú o  /              \³_/\_/         \_/~~~~~~\_/
  '-³-'      Start/-³-'                ³ ³³             ³~~~~~~³

   NEON         REGULATOR             HEATED        HEATED HIGH CURRENT
 80V 2mA        150V 80mA            THYRATRON        GAS RECTIFIER

NOTES:          OA2 = 150v           much typ     1007 cold kathode (octal)
------          OB2 = 90v            See book:      (US militair app's)
(From ON4CBL)   150C1K (octal)       EEV-GenE.            ...

More complex neon ones make up NIXI number display tubes, & nowadays Mercury
vapour ones make fluorescent lamps & the hart of Plasma TV display panels.

With liquid Mercury as a Cathode, large ones use (before the silicon diode)
to be used as large poly phase rectifiers, with 3, 6, or even 12 Anodes, many
Amps at several kVs can be rectified this way.

    A1  A2  A3  A4  A5  A6
  .-³---³---³---³---³---³-.
 / ÄÁÄ ÄÁÄ ÄÁÄ ÄÁÄ ÄÁÄ ÄÁÄ \
³                           ³
 \_ Ú         o           _/
   ~³~~~~~~~~~³~~~~~~~~~~~
 Starter      C



See my bulletins on "Early AVO Valve Tester", "Old Valve Radios", "Microwave
Ovens" & for PAs "4CX250B PA Regulated Supplies" & "4CX250B PA Timing &
Control", & also "Reforming Caps" or "Oscilloscopes" for CRT information.


Why Don't U send an interesting bul?

73 De John G8MNY @ GB7CIP


Lese vorherige Mail | Lese naechste Mail


 27.11.2024 02:52:28lZurueck Nach oben